QIDAMT
| Product Name | 1060 Aluminum Plate |
| Alloy | 6005 aluminum are alloyed with magnesium and silicon, are easy to machine and can be precipitation hardened that not to the high strength that 2000 and 7000 series can reach. |
| Temper | H112,H113,H12 etc. |
| Thickness | 0.2mm to 12mm |
| Width | For coil: 600mm ~ 2000mm, or as customize |
| For sheet: 20mm ~ 2200mm, or as customize | |
| Weight/Coil | As the customer’s request |
| MOQ | 3 ton |
| Delivery time | Aound 30 days |
| Payment terms | T/T L/C |
| Container | 20ft: 5898mm(L)*2352mm(W)*2393mm(H) Loading 18-25 tons 40ft:12032mm(L)*2352mm(W)*2393mm(H) Loading 25-27 tons |
| Packing | 3 layers of packing. Inside is craft paper, Middle is water plastic film and outside GI steel sheet to be covered by steel strips |
Chemical Composition
| Chemical Composition % | ||||||||||
| Si | Fe | Cu | Mn | Mg | Cr | V | Zn | Ti | Al | |
| 1070 | ≤0.25 | ≤0.35 | ≤0.05 | ≤0.03 | ≤0.03 | / | ≤0.05 | ≤0.05 | ≤0.03 | 99.6-100 |
Mechanical Properties
| Mechanical Properties | |
| Property | Value |
| Elastic(Young’s, Tensile) Modulus | 68GPa |
| Fatigue Strength | 15 to 50 Mpa |
| Elongation at Break | 1.1 to 30% |
| Shear Modulus | 26GPa |
Application:
- Manufacture of railroad tank car
- Chemical Equipment
Fabrication Response
Hardening
Aluminum 1060 alloy can be hardened only form cold working. Tempers H18, H16, H14 and H12 are determined based on the amount of cold working impacted to this alloy.
Annealing
Aluminum 1060 alloy can be annealed at 343℃ and then cooled in air.
Cold working
Aluminium 1060 has excellent cold working characteristics and conventional methods are used to readily cold work this alloy.
Forging
Aluminum 1060 alloy can be forged between 510-371℃.
Variations
1.1060-H112 Aluminum
1060-H112 is 1060 aluminum in the H112 temper. This temper is actually just a variation on F (as-fabricated) that allows for the possibility of very limited strain hardening or heat treatment, under certain conditions.
It has the second lowest strength and second highest ductility compared to the other variants of 1060 aluminum.
2.1060-H113 Aluminum
1060-H113 is 1060 aluminum in the H113 temper. This temper is a very specific variation on H112 that only applies to standard tube products.
It has the lowest strength compared to the other variants of 1060 aluminum.
3.1060-H12 Aluminum
1060-H12 aluminum is 1060 aluminum in the H12 temper. To achieve this temper, this metal is strain hardened to a strength that is roughly a quarter of the way between annealed(O) and full -hard (H18).
4.1060-H14 Aluminum
1060-H14 aluminum is 1060 aluminum in the H14 temper. To achieve this temper, this metal is strain hardened to a strength that is roughly a quarter of the way between annealed(O) and full -hard (H18).
5.1060-H16 Aluminum
1060-H16 aluminum is 1060 aluminum in the H16 temper. To achieve this temper, this metal is strain hardened to a strength that is roughly 3/4 of the way between annealed(O) and full -hard (H18).
6.1060-H18 Aluminum
1060-H18 aluminum is 1060 aluminum in the H18 temper. This is the strongest temper normally produced through the action of only strain hardening.
7.1060-H22 Aluminum
1060-H22 aluminum is 1060 aluminum in the H22 temper. To achieve this temper, this metal is strain hardened,and then partially annealed, to a strength that is roughly a quarter of the way between annealed(O) and full -hard (H28).
8.1060-H24 Aluminum
1060-H24 aluminum is 1060 aluminum in the H24 temper. To achieve this temper, this metal is strain hardened,and then partially annealed, to a strength that is roughly halfway between annealed(O) and full -hard (H28).
9.1060-H26 Aluminum
1060-H26 aluminum is 1060 aluminum in the H26 temper. To achieve this temper, this metal is strain hardened,and then partially annealed, to a strength that is roughly 3/4 of the way between annealed(O) and full -hard (H28).
10.1060-H28 Aluminum
1060-H28 aluminum is 1060 aluminum in the H 28 temper. This is the strongest temper normally produced through the action of strain hardening followed by partial annealing. It is closely related to related H18.
11.1060-O Aluminum
1060-O aluminum is 1060 aluminum in the annealed condition. It has the highest ductility compared to the other variants of 1060 aluminum.
Process Flow
FAQ
1. Q:Are you a manufacturer or trading company?
A: We are a manufacturer, can do OEM and ODM.
2. Q: Can i get some samples? What product information do i need to provide?
A: Yes, we have small samples, like A4 size. You need to provide the grade (ALLOY NUMBER) and temper, thickness, width,length and the quantity.
3. Q: How does your factory do regarding quality control?
A: Quality is priority. Our factory has gained SGS authentication. We guarantee the goods out form our factory 100% qualified. And each process, we have very strict operation and arrange 2 technicians to inspect. After the products are finished, we will make the last test to pick up the unqualified products.
4. Q：What is your payment?
A: Generally we accept 30% T/T as deposit and 70% against with B/L copy
Packing & Shipping
